Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 24, 2007 18:45:33 GMT
Was on the Central this afternoon between NHG - CHL and return, and despite the trains I was on were getting really lousy codes (congestion and slower speeds) the station approaches didn't seem anywhere near as quick as they usually do. Even coming in at a relatively low speed, the train was coasting/on a light brake for a lot longer than normal, and also trains were braking a lot earlier than usual. Has the ATO been altered slightly, or was it just me  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 24, 2007 19:15:08 GMT
You probably had trains in front that had just departed, and the ATP was holding the codes down to enforce a safe overlap on the station approaches. The signalling on the Central can actually handle quite tight run-in/run-out at the Zone 1 stations.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 24, 2007 21:10:16 GMT
I've said it before on the forums and to you, Alex, but you can actually see the train behind you pulling into the platform in the in-cab monitors as you pull out...
Sam
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 27, 2007 6:38:55 GMT
The Central's signalling supports approx 60sec roll out roll in times in the central area, which is good, but not impressive. (It's roughly equal to having 3 multiple home signals). The speed at which the train runs into the station behind the other depends on how close it is to the train in front, the spacing of the signal blocks, and the speed limits for that area.
In the case that Alex observed, maybe the train was being driven in CM?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 27, 2007 8:54:39 GMT
In the case that Alex observed, maybe the train was being driven in CM? That is more likely to be the case |
|
towerman
My status is now now widower
Posts: 2,970
|
Post by towerman on Jan 27, 2007 21:29:03 GMT
All lines are due to get a new WTT in May for Ken's late running at weekends.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 31, 2007 15:30:27 GMT
In the case that Alex observed, maybe the train was being driven in CM? I thought CM was banned in tunnel sections - mind you it could have been............. |
|
|
|
Post by ongarparknride on Jan 31, 2007 23:49:40 GMT
Hi towerman,
Sorry but could you say what "WTT" means please?
Only just recently picked up Sonya got her name from "It getS ON YA nerves"
:-)
Thanks and cheers,
cheers
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 31, 2007 23:51:00 GMT
Sorry but could you say what "WTT" means please? Working Timetable |
|
|
|
Post by ongarparknride on Feb 1, 2007 0:19:47 GMT
Thank you "adw".
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 23, 2007 12:11:40 GMT
With the target speeds, which bits of line could you get a target of 100 kph? I know between North and East Acton it can go up that high.
|
|
Tom
Administrator
Signalfel?
Posts: 4,196 
|
Post by Tom on Feb 23, 2007 14:25:55 GMT
All the trains are currently restricted to 85kph post Chancery Lane.
Even if they weren't, I'd be surprised if you could reach 100 on that stretch. It used to be quite common between West Ruislip and Ruislip Gardens though.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 23, 2007 14:32:56 GMT
So that's about 52.8 mph. Is it fair to assume that between WER and EAA that you could get a 100 kph target along the whole thing? My list of speed restrictions dating from 1993 says this is possible.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 26, 2007 11:39:11 GMT
Blimey! Thanks auxsetreq fot that deatiled answer - interesting stuff  |
|
